Post by Lejam on Jun 7, 2011 19:03:42 GMT -5
I remember someone (sorry I forgot) from this forum told us about a car wax
to use to protect Diecast Toys... (what's the name of this wax ?)
I also found something interesting :
www.kaskus.us/showthread.php?p=438646880#post438646880
Google trad -> Malaysian :
"1. Before Cleaning Up
2. The Tools, gloves, delicate,
Dust-off, soft toothbrush, cotton buds,
blue kit, brush a little hard
& Soft tissue for the baby.
3. First remove all parts of the SOC can
released, for example the head, arms, missile,
and others.
We are starting small with little Parts KIT.
4. carefully at the section / parts which no paint or sticker
of its manufacture, because there are too many or chemical KIT
will destroy. I only make one part-KIT
no paint or sticker, to head the image BossBorot
My eyes are not KIT.
5. the polishing begins, little by little all
parts we spread the KIT, not too much, because
Susan will be clean.
If we have to wipe the fingers,
the pattern of play, feel where the parts
The need to dirty extra attention.
let stand down after about 5 minutes,
KIT or until dry.
rough polishing results will be like this,
(More or less depending on the number of KIT-in-one).
6. KIT after dry, then we use
Thin gloves, gloves that I mean
is worn by the bride, not a glove
porters of the building. or a special glove that Chogokin
can be gained when buying the SOC-GX45 MazingerZ.
Why use gloves?
because we do not want there to be software & sweat patch
in the SOC that we clean. acidic sweat
which can cause corrosion or rust on the SOC favorite.
7. take some tissue, began to do the cleaning.
be careful when handling the SOC, because we
wearing gloves, so the SOC is
Smooth, clean & easy to be rising.
Here I started to clean up from the stomach.
8. after all is finished we went into the detailing.
start with detailing, detailing gross / large.
Here I begin with the sidelines of the feet & hands
using a large brush & is a bit rough.
9. detailing extended into smaller parts &
brush of course also more subtle.
typically for parts, heads, hands, arms,
and others.
10.detailing end, now use cotton buds
to-reach areas are not able to reach
by the comb over.
including the part of this
11. after all the clean parts back together.
and the pose. Final step before the display is
spray using Dust Off, high pressure wind blow.
this is to remove all the fine dust that stick
in the SOC is clean.
12. final results
The time needed to clean up a SOC
is about 30 minutes. Depending on the complexity of SOC
itself.
if the later SOC dusty, can be cleaned with Dust Off
Micro Fibre or napkins, polishing is only effective
performed at 6 months.
NB:
All Tools can be purchased at Ace Hardware,
except wedding gloves.
Hope helps.
thanks.
Thanks & Cheers KASKUS!"
to use to protect Diecast Toys... (what's the name of this wax ?)
I also found something interesting :
www.kaskus.us/showthread.php?p=438646880#post438646880
Google trad -> Malaysian :
"1. Before Cleaning Up
2. The Tools, gloves, delicate,
Dust-off, soft toothbrush, cotton buds,
blue kit, brush a little hard
& Soft tissue for the baby.
3. First remove all parts of the SOC can
released, for example the head, arms, missile,
and others.
We are starting small with little Parts KIT.
4. carefully at the section / parts which no paint or sticker
of its manufacture, because there are too many or chemical KIT
will destroy. I only make one part-KIT
no paint or sticker, to head the image BossBorot
My eyes are not KIT.
5. the polishing begins, little by little all
parts we spread the KIT, not too much, because
Susan will be clean.
If we have to wipe the fingers,
the pattern of play, feel where the parts
The need to dirty extra attention.
let stand down after about 5 minutes,
KIT or until dry.
rough polishing results will be like this,
(More or less depending on the number of KIT-in-one).
6. KIT after dry, then we use
Thin gloves, gloves that I mean
is worn by the bride, not a glove
porters of the building. or a special glove that Chogokin
can be gained when buying the SOC-GX45 MazingerZ.
Why use gloves?
because we do not want there to be software & sweat patch
in the SOC that we clean. acidic sweat
which can cause corrosion or rust on the SOC favorite.
7. take some tissue, began to do the cleaning.
be careful when handling the SOC, because we
wearing gloves, so the SOC is
Smooth, clean & easy to be rising.
Here I started to clean up from the stomach.
8. after all is finished we went into the detailing.
start with detailing, detailing gross / large.
Here I begin with the sidelines of the feet & hands
using a large brush & is a bit rough.
9. detailing extended into smaller parts &
brush of course also more subtle.
typically for parts, heads, hands, arms,
and others.
10.detailing end, now use cotton buds
to-reach areas are not able to reach
by the comb over.
including the part of this
11. after all the clean parts back together.
and the pose. Final step before the display is
spray using Dust Off, high pressure wind blow.
this is to remove all the fine dust that stick
in the SOC is clean.
12. final results
The time needed to clean up a SOC
is about 30 minutes. Depending on the complexity of SOC
itself.
if the later SOC dusty, can be cleaned with Dust Off
Micro Fibre or napkins, polishing is only effective
performed at 6 months.
NB:
All Tools can be purchased at Ace Hardware,
except wedding gloves.
Hope helps.
thanks.
Thanks & Cheers KASKUS!"
.
