|
|
Post by Lejam on Nov 8, 2014 17:54:44 GMT -5
|
|
|
|
Post by coldiron on Nov 8, 2014 22:32:04 GMT -5
I was just talking to someone about this. Seems they had good results with it and it cut down the time to finish the design. They said they thinned it for high res models.
|
|
|
|
Post by TheMazingerZ on Nov 9, 2014 14:40:28 GMT -5
So, the shipping from smooth-on is almost $19 for the 24oz kit. I don't know... May have to wait for you guys to try it and give your recommendations on it.  }D |
|
|
|
Post by magengar on Nov 9, 2014 18:07:45 GMT -5
Wow! Great find, brother! Man, I'd like to try that product to patch a large hole in the knuckle of my jumbo right Gaiking fist. And I could also use it to coat and seal styrofoam sculpted mock models so that I can cast rubber molds from them. Thaaaaanks!  zozo-mag |
|
|
|
Post by TheMazingerZ on Nov 10, 2014 22:12:20 GMT -5
Almost there! Finally managed to make the Heat Blade with my 3D printer!!! So just a little more sanding, some primer, paint, and it'll be done!   }D |
|
|
|
Post by TheMazingerZ on Nov 19, 2014 13:30:21 GMT -5
|
|
|
|
Post by droutmaster on Nov 19, 2014 18:47:50 GMT -5
There some videos reviews about that printer if you want to see it TMZ
not a bad printer just the filament cartridge is the only problem for now.
|
|
|
|
Post by TheMazingerZ on Nov 19, 2014 19:02:07 GMT -5
OMG! Just pre-ordered it!!! Thanks bro! Anyone wants a cheap Davinci 1.0??? }D |
|
|
|
Post by mojacko on Nov 20, 2014 7:47:04 GMT -5
|
|
|
|
Post by TheMazingerZ on Dec 22, 2014 1:18:02 GMT -5
 }D |
|
|
|
Post by B- on Dec 26, 2014 6:31:59 GMT -5
oh wow those are the nerdiest bunch of dudes ive seen since high school lol. |
|
|
|
Post by TheMazingerZ on Jan 15, 2015 18:21:28 GMT -5
So, the Grengus C3 is not finished yet, but today I started working on a 3D printed anime style God Mazinger figure.  The kilt design is a major beetch! All those plates... good Lord! Gonna have to put a lot of work into this guy. }D |
|
|
|
Post by TheMazingerZ on Jan 16, 2015 15:05:00 GMT -5
Okay, after thinking about it, I went in a different direction for the kilt. Here is the prototype:  It is not articulated, but I think it will work out fine. }D |
|
|
|
Post by TheMazingerZ on Feb 9, 2015 0:57:50 GMT -5
Software makes a huge difference! Just purchased Simplify3D a few days ago, and the results on the Da Vinci printer are awesome! Check this out:  And that's just a test figure, with the worst print settings! Now we're cooking with gas!!! }D |
|
|
|
Post by TheMazingerZ on Feb 9, 2015 15:17:35 GMT -5
With the second forearm and its tail...  }D |
|
The Great Robot Base
Junior Robot
Photo from: http://www.flickr.com/photos/24137579@N05/6847726444/in/photost
Posts: 38
|
Post by The Great Robot Base on Feb 10, 2015 18:44:27 GMT -5
Looks fearsome! The detail of sculpt possible looks very good. The engineering design also looks well done for posing plus stable balance. With the second forearm and its tail... |
|
|
|
Post by Fontes on Feb 10, 2015 18:58:26 GMT -5
3D printing is something I've had my eyes on fir a fair bit. Too big for my pocket, unfortunately, so in the short term I might take a look at Shapeways or something of the sort.
And TMZ's piece of work there is lookin' good!
|
|
|
|
Post by TheMazingerZ on Feb 13, 2015 0:24:11 GMT -5
Thanks! Soon this figure will have to have its own thread...  Different heads now...  }D |
|
The Great Robot Base
Junior Robot
Photo from: http://www.flickr.com/photos/24137579@N05/6847726444/in/photost
Posts: 38
|
Post by The Great Robot Base on Feb 13, 2015 17:03:01 GMT -5
|
|
|
|
Post by TheMazingerZ on Feb 13, 2015 19:38:29 GMT -5
Thanks bro! It takes me a while to get the progress going. Source material for this particular character I want to make is very hard to find.  As far as the printer, I'm using a regular Da Vinci 1.0. The reviews for the AIO I wanted were horrible, so I didn't get it. }D |
|
